Just How to Remove and Also Replace a Bathtub
Just How to Remove and Also Replace a Bathtub
Blog Article
The writer is making a number of good points related to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this content which follows.
Setting up a bathtub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a new one is likewise a reasonably tough project. If the old tub is conveniently available, the task can move immediately; if you have to open a wall surface to get rid of the old tub and also position the brand-new bathtub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need an assistant to vacate the old tub as well as embeded in the new one. See to it you have actually qualified on your own for the work and are comfortable trying it. Rather than employing a service provider to take over a halfway-completed job, it is far better to consider utilizing one prior to you begin. Possibilities are you might need a specialist plumber to make tube connections.
This short article will certainly aid you install a new tub in your washroom if you have actually already purchased a brand-new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your tools as well as product list should comprise the following:
Getting ready for the Setup
To start with, the sustaining structure supplied with the bath should be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Ensure you use all of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its last position.
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited accessibility that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipes. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing substance.
Before carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Utilizing the two wood boards under its feet, place the tub in the called for setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub up until the level reads degree.
To mount taps, fit the bottom of the furthest adaptable faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the same for the other tap.
Turn on the water and also examine all joints as well as brand-new pipework for leaks and tighten them if necessary. Fill the bathtub as well as additionally inspect the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait till the tub has been used at the very least when as this will settle it right into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Safeguard the faucet in position with the maker given backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet adapters. The previous kind needs to be connected to the tap ends first, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, creating the water to pass through the wall between the bath as well as the tiling, resulting in complications with moisture as well as feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes as well as cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub is in use. The sealant can break relatively early if you do not take into consideration this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the market. It is recommended to fit the floor tiles using water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid person who reads on Installing A Bathtub, I figured sharing that piece was a good idea. Loved our article? Please share it. Help other people find it. Many thanks for your time. Visit again soon.
About This
Report this page